Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Ultramid® A3L HP - PA66 - BASF

Material Data Center offers the following functions for Ultramid® A3L HP:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Ultramid A datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
기계적 특성 - 열적 특성 - 기타 특성
Any use of this information falls under the rules of our disclaimer.
제품 설명서
Ultramid® A3L HP is an unreinforced, impact modified, high flow, Polyamid 66 for injection molding. This grade has excellent flow and improved ambient and low temperature toughness.

Typical applications include fasteners and clamps.
기계적 특성건조/응축단위시험규격
ISO 데이터
인장탄성률 2440 / - MPa ISO 527
항복강도 63.5 / - MPa ISO 527
항복변형률 6.2 / - % ISO 527
파단시 평균신율 28 / - % ISO 527
챠피 노치드 충격 강도, +23°C 19 / - kJ/m² ISO 179/1eA
챠피 노치드 충격 강도, -30°C 14 / - kJ/m² ISO 179/1eA
열적 특성건조/응축단위시험규격
ISO 데이터
녹는점, 10°C/min 262 / * °C ISO 11357-1/-3
하중하에서의 변형온도, 1.80 MPa 70 / * °C ISO 75-1/-2
하중하에서의 변형온도, 0.45 MPa 192 / * °C ISO 75-1/-2
기타 특성건조/응축단위시험규격
밀도 1100 / - kg/m³ ISO 1183
특징
생산 공정
사출 성형
지역별 검색
쨘횕쩐횈쨍횧쨍짰횆짬
기타 정보
사E성
Nylon 66 materials must be properly dried in order to provide parts
with optimum strength and toughness. Nylon 66 materials are
hygroscopic and will become degraded by excessive moisture during the
injection molding process. For unopened bag/box, dry at 140F (60C) for
1-2 hours. For material exposed to the atmosphere, if additional
drying is needed, dry at 150F (66C) or until the moisture level is
between 0.04 - 0.20%.
PROCESSING
Melt Temperature: 288 – 305C (550 – 580F)
Mold Temperature: 60 – 100C (140 – 212F)
Injection Pressure: 35 – 125 MPa (5000 – 18000 psi)
Back Pressure: 0 – 0.35 MPa (0 – 50 psi)
Screw RPM 40 – 80
Screw Compression Ratio:3:1 – 4:1

This product can be processed over a wide range of mold
temperatures; however, for applications where aesthetics are
critical, a mold surface temperature of 60-100C (140-212F)
is recommended.

Injection pressure controls the filling of the part and should
be applied for 90% of ram travel. Packing pressure affects
the final part and can be used effectively in controlling
sink marks and shrinkage. It should be applied and maintained
until the gate area is completely frozen off.

Fast fill rates are recommended to insure uniform melt
delivery to the cavity and prevent premature freezing.
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.